MCP2562FDT-E/SN

Inventory search

Technical information

MCP2562FDT-E/SNYour current position：Home > MCP2562FDT-E/SN

View large image

MCP2562FDT-E/SN
BaoxingWei inventory：5000 PCS
Mfg： MICROCHIP
Package： SOP8
D/C： 22+
Note： Supply only imported original genuine Shenzhen and Hongkong in stock
PDF：

MCP2562FDT-E/SN

The MCP2561/2FD is a Microchip Technology Inc. second generation high-speed CAN transceiver. It offers the same features as the MCP2561/2. Additionally, it guarantees Loop Delay Symmetry in order to support the higher data rates required for CAN FD. The maximum propagation delay was improved to support longer bus length. The device meets the automotive requirements for CAN FD bit rates exceeding 5 Mbps, low quiescent current, electromagnetic compatibility (EMC) and electrostatic discharge (ESD). The device family members are MCP2561FD with SPLIT pin and MCP2562FD with VIO pin.

MCP2561/2FD是Microchip Technology Inc .的第二代高速CAN收发器。它提供与MCP2561/2相同的功能。此外，它保证环路延迟对称，以支持CAN FD所需的更高数据速率。改进了最大传播延迟，以支持更长的总线长度。该器件满足汽车应用对CAN FD比特率超过5 Mbps、低静态电流、电磁兼容性(EMC)和静电放电(ESD)的要求。该器件系列包括带开口销的MCP2561FD和带VIO引脚的MCP2562FD。

Product Features 产品特性

Maximum Propagation Delay: 120 ns
Loop Delay Symmetry: -10%/+10% (2 Mbps)
Implements ISO-11898-2 and ISO-11898-5 Standard Physical Layer Requirements
AEC-Q100 Grade 0
Very Low Standby Current (5 μA, typical)
VIO Supply Pin to Interface Directly to CAN Controllers and Microcontrollers with 1.8V to 5.5V I/O
SPLIT Output Pin to Stabilize Common Mode in Biased Split Termination Schemes
An Unpowered Node or Brown-Out Event will Not Load the CAN Bus
Permanent Dominant Detection on TXD
Permanent Dominant Detection on Bus
Power-on Reset and Voltage Brown-Out Protection on VDD Pin
Protection Against Damage Due to Short-Circuit Conditions (Positive or Negative Battery Voltage)
Protection Against High-Voltage Transients in Automotive Environments
Automatic Thermal Shutdown Protection
Suitable for 12V and 24V Systems
Radiated emissions @ 2 Mbps with Common Mode Choke (CMC)
DPI @ 2 Mbps with CMC
High ESD Protection on CANH and CANL, meeting IEC61000-4-2 up to ±14 kV
Available in PDIP-8L, SOIC-8L and 3x3 DFN-8L
Extended (E): -40°C to +125°C
High (H): -40°C to +150°C
最大传播延迟:120 ns
环路延迟对称性:-10%/+10% (2 Mbps)
实施ISO-11898-2和ISO-11898-5标准物理层要求
AEC-Q100 0级
非常低的待机电流(5 μA，典型值)
VIO电源引脚通过1.8V至5.5V I/O直接与CAN控制器和微控制器接口
分离输出引脚，用于稳定偏置分离端接方案中的共模
未通电节点或掉电事件不会加载CAN总线
TXD上的永久优势检测
总线上的永久主导检测
VDD引脚上的上电复位和电压掉电保护
防止因短路条件(正极或负极电池电压)造成的损坏
汽车环境中的高压瞬变保护
自动热关机保护
适用于12V和24V系统
共模扼流圈(CMC)下2 Mbps时的辐射发射
使用CMC时2 Mbps的DPI
CANH和CANL上的高ESD保护，满足高达14 kV的IEC61000-4-2要求
提供PDIP-8L、SOIC-8L和3x3 DFN-8L三种型号
扩展(E):-40℃至+125℃
高(高):-40摄氏度至+150摄氏度

Parametrics 参数化

CAN FD	Yes
Bitrate Max (MBits/s)	8
Operating Temperature Max. (C)	150
Operating Temperature Min. (C)	-40
Operating Voltage Max. (V)	5.5
Operating Voltage Min. (V)	4.5

CAN FD	是
最大比特率(兆比特/秒)	8
最高工作温度。(三)	150
最低工作温度。(三)	-40
最大工作电压。㈤	5.5
最小工作电压。㈤	4.5

Home

Products

Stock

Service

About Us

Contact Us

View large image

Product Features 产品特性

Parametrics 参数化

Product Features 产品特性

Parametrics 参数化

Skype

whatapp

Hotline

E-mail